![linux network driver linux network driver](https://image.slideserve.com/867328/linux-network-driver-framework-opening-and-closing-l.jpg)
- LINUX NETWORK DRIVER HOW TO
- LINUX NETWORK DRIVER INSTALL
- LINUX NETWORK DRIVER DRIVERS
- LINUX NETWORK DRIVER DRIVER
- LINUX NETWORK DRIVER PC
Ping -c 5 8.8.8.8 # This is Google's domain name server Sudo iptables -A POSTROUTING -t nat -j MASQUERADE -s 10.0.1.0/24Īnd then for reasons I don't fully undestand, I had to configure usb0 on the host again: There is a lot of information on how the Internet giving more detailed explanation.Įcho 1 | sudo tee /proc/sys/net/ipv4/ip_forward > /dev/null
LINUX NETWORK DRIVER PC
It only works if your host PC doesn't have a firewall enable.
LINUX NETWORK DRIVER HOW TO
The following shows how to enable, test, and disable. If your host PC is connected to the Internet (through WiFi or Ethernet), then you can allow the target device to share the host PC's Internet connection. Look at the values of RX packets: and TX packets.īridging host PC to allow device to reach the Internet On the host PC, verify the number of packet sent and received is not zero With the route showing the default gateway is using usb0 With an entry from the route output that looks likeĭestination Gateway Genmask Flags Metric Ref Use Iface G_ether gadget: high speed config #1: CDC Ethernet (ECM)įor this simple example, fixed IP addresses are assigned to the both the host PC USB network interface and the target device USB network interface. When you connect the cable, in the target device console, you should see: TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 On the host you can verify the new usb0 interface exists by running:
LINUX NETWORK DRIVER DRIVER
Jun 6 10:15:29 contra-lx kernel: usbcore: registered new interface driver cdc_ether Jun 6 10:15:29 contra-lx kernel: usbcore: registered new interface driver cdc_subset Jun 6 10:15:29 contra-lx kernel: cdc_subset: probe of 1-4.4.2:1.0 failed with error -22 Jun 6 10:15:29 contra-lx kernel: usb 1-4.4.2: new high speed USB device using ehci_hcd and address 47
![linux network driver linux network driver](https://www.intel.com/content/dam/altera-www/global/en_US/documentation/swn1503506366945/vzu1503621390013.jpg)
The messages file on the host PC should indicate the new USB device was detected. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0īefore connecting the target device to the host PC, watch the syslog, by running the following command on the host PC:Ĭonnect the USB cable between the target device and the host PC. RX packets:0 errors:0 dropped:0 overruns:0 frame:0 Usb0 Link encap:Ethernet HWaddr BE:B5:85:EF:48:33 You can then verify the usb0 network interface exists: G_ether gadget: Ethernet Gadget, version: Memorial Day 2008 G_ether gadget: using random host ethernet address G_ether gadget: using random self ethernet address
LINUX NETWORK DRIVER INSTALL
Selects: FEATURE_HAVE_RPC & FEATURE_SYSLOGīuild the SDK and install the new images to the target hardware.Īfter booting the target hardware to a shell prompt, run: Prompt: Support mounting NFS file systems If you want the target to mount a host PC directory using NFS, then also enable NFS mount support in busybox: Prompt: Ethernet Gadget (with CDC Ethernet support)ĭefined at drivers/usb/gadget/Kconfig:628
LINUX NETWORK DRIVER DRIVERS
Generally it is best to build USB gadget drivers as modules instead of building them into the kernel so you can unload one and load another.
![linux network driver linux network driver](https://www.intel.com/content/dam/develop/external/us/en/images/fig1-solution-components-and-interactions-744724.png)
The USB Ethernet network gadget driver caused the device to appear to be a USB network dongle when connected to a host computer. DM365 - How to configure DM365 for USB host, device and OTG support.10.2 NFS mount failed reason given by server: Permission deniedĬonfigure hardware for USB OTG or USB device supportĭepending on your hardware, you can use either USB OTG or USB device to enable support for USB networking.10 Debugging and resolving common errors.7 Bridging host PC to allow device to reach the Internet.3 Load USB Ethernet network gadget driver.2 Build USB Ethernet network gadget driver.1 Configure hardware for USB OTG or USB device support.